STEEL PRODUCTION AND ITS ROLE IN MECHANICAL ENGINEERING.

K.O. Polvanov

doi:10.37547/

PDF

Published: 2025-06-17

DOI: https://doi.org/10.37547/

Keywords:

Metal, mechanical engineering, steel, casting, tool steel, high-speed steel.

Polvanov K.O.

Urgench State University named after Abu Rayhan Beruni, Senior Lecturer of the Department of "Transport Systems" at the Faculty of Engineering:

Abstract

Deep cutting is also achieved by expanding the cutting and technological properties of steel through the addition of cobalt (Co), molybdenum (Mo), and increasing the amount of vanadium. Steels P18F2K5 (cobalt-coated), P9K5, P9K10, and P10FK5 are considered highly heat-resistant and are recommended for heat-resistant austenitic steels and hardened steels.

Downloads

Download data is not yet available.

Issue

Vol. 5 No. 6 (2025): International Bulletin of Applied Science and Technology

Section

Articles

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

STEEL PRODUCTION AND ITS ROLE IN MECHANICAL ENGINEERING. (2025). International Bulletin of Applied Science and Technology, 5(6), 260-262. https://doi.org/10.37547/

References

1.Yu.K. Kozlov — “Materialshunoslik”, Toshkent, “O‘qituvchi”, 1987

2.A.A. Mirzayev, B.N. Fayzimatov, T.T. Turaev, A.E. Sotvoldiev, R.S. Ulug‘xo‘jayev, E.T. Mamurov, B. Jursanov, M. Rahmonqulov — “Metallarga ishlov berish texnologiyasi”, “Sharq” nashriyoti, B.N. Fayzimatov va T.Turaev tahriri ostida, Toshkent, 2005

3.B.A. Mirboboyev — “Materialshunoslik”.

Similar Articles

Shokhrukh Shukhratovich Akhmadaliev, Khasanov Kamoliddin Akmal ugli, Saydumarov Botir Muradovich, DEVELOPMENT OF AN UPPER-BOUND METHOD FOR EXTRUSION STAMPING OF A CONICAL FLANGE , International Bulletin of Applied Science and Technology: Vol. 5 No. 6 (2025): International Bulletin of Applied Science and Technology
Qabulova Nilufar Jalilovna, Khalmatov Musltiddin Mukhammatovich, COMPARISON OF THE RESULTS IN THE STUDY OF ATMOSPHERIC AIR POLLUTION WITH DUST , International Bulletin of Applied Science and Technology: Vol. 3 No. 6 (2023): International Bulletin of Applied Science and Technology
Bakhodir Polatov, OBTAINING A WEAR-RESISTANT COATING USING FLAME SPRAYING FOLLOWED BY MELTING , International Bulletin of Applied Science and Technology: Vol. 4 No. 8 (2024): International Bulletin of Applied Science and Technology
Amanbaev Nursultan Salamat o‘g‘li, A PROGRAM FOR USING THE AUTOMATED MODEL OF THE SYSTEM PROJECT IN THE CONTROL OF TECHNOLOGICAL PROCESSES , International Bulletin of Applied Science and Technology: Vol. 4 No. 4 (2024): International Bulletin of Applied Science and Technology
Kulahmetov Oybek Pochchahonovich, Mirzabekova Umida Nishanbayeva, TALGO HIGH-SPEED PASSENGER TRAIN AND SAFETY SYSTEM ANALYSIS , International Bulletin of Applied Science and Technology: Vol. 4 No. 7 (2024): International Bulletin of Applied Science and Technology
Kulahmetov Oybek Pochchahonovich, Mirzabekova Umida Nishanbayeva, HIGH-SPEED TRAIN MAINTENANCE SYSTEM SHAPING AND EVOLVING IN THE REPUBLIC OF UZBEKISTAN , International Bulletin of Applied Science and Technology: Vol. 4 No. 7 (2024): International Bulletin of Applied Science and Technology
N.B. Pirmatov, J.A. Nizamov, Sh.O. Ergashov, EXPERIMENTS WITH ASYNCHRONOUS MOTORS EXTERNAL MAGNETIC FIELDS , International Bulletin of Applied Science and Technology: Vol. 3 No. 12 (2023): International Bulletin of Applied Science and Technology
Djumbabayev Alizhan Bakishevich, Artykov Sarvar Sattaraliyevych, Karimov Abbasjon Israilovich, DETERMINATION OF TIME STANDARDS FOR MAINTENANCE AND REPAIR OF CHEVROLET NEXIA CAR CLUTCH , International Bulletin of Applied Science and Technology: Vol. 3 No. 2 (2023): International Bulletin of Applied Science and Technology
B.B.Qarshiyev, MAIN DIRECTIONS IN THE DEVELOPMENT OF STEAM EDUCATION ELEMENTS. , International Bulletin of Applied Science and Technology: Vol. 4 No. 6 (2024): International Bulletin of Applied Science and Technology
Abdirazakov Akmal Ibrahimovich, Mavlanov Zafar Alanazarovich, Halimov Shohrux Komiljon o’g’li, SELECTION AND BASED ON MODE PARAMETERS IN SLOPE DRILLING , International Bulletin of Applied Science and Technology: Vol. 3 No. 3 (2023): International Bulletin of Applied Science and Technology

You may also start an advanced similarity search for this article.

Article Sidebar

Main Article Content